-
1 test current
испытательный ток
Ток, вызывающий падение напряжения в цепи
[ ГОСТ Р 61557-1-2006]EN
test current
current that causes a voltage drop in a circuit
[IEC 61557-3, ed. 2.0 (2007-01)]FR
courant d'essai
dispositif provoquant une chute de tension dans un circuit
[IEC 61557-3, ed. 2.0 (2007-01)]-
Если испытательный ток ниже номинальной наибольшей отключающей способности, на выходной стороне выключателя следует предусмотреть дополнительные импедансы Z1.
[ ГОСТ Р 50345-99( МЭК 60898-95)] - При испытании однофазным переменным током или постоянным током испытательный ток в цепи должен быть не ниже, установленного в стандартах на конкретные виды аппаратов.
-
Испытательный ток следует определять с помощью осциллографа.
[ ГОСТ 2933-83]
Тематики
- электротехника, основные понятия
EN
FR
3.3 испытательный ток (test current): Ток, вызывающий падение напряжения в цепи.
Источник: ГОСТ Р МЭК 61557-3-2006: Сети электрические распределительные низковольтные напряжением до 1000 В переменного тока и 1500 В постоянного тока. Электробезопасность. Аппаратура для испытания, измерения или контроля средств защиты. Часть 3. Полное сопротивление контура оригинал документа
3.3 испытательный ток (test current): Ток, вызывающий падение напряжения в цепи.
Источник: ГОСТ Р 54127-3-2011: Сети электрические распределительные низковольтные напряжением до 1000 В переменного тока и 1500 В постоянного тока. Электробезопасность. Аппаратура для испытания, измерения или контроля средств защиты. Часть 3. Полное сопротивление контура оригинал документа
3.3.3 испытательный ток (test current): Ток, вызывающий падение напряжения в цепи.
Источник: ГОСТ Р МЭК 61557-1-2005: Сети электрические распределительные низковольтные напряжением до 1000 В переменного тока и 1500 В постоянного тока. Электробезопасность. Аппаратура для испытания, измерения или контроля средств защиты. Часть 1. Общие требования оригинал документа
15.2.6 испытательный ток (test current): Значение тока, установленное изготовителем для контактного зажима или соединения. Когда контактные зажимы являются отдельными компонентами светильника, испытательным должен быть ток, нормируемый для компонента.
Источник: ГОСТ Р МЭК 60598-1-2011: Светильники. Часть 1. Общие требования и методы испытаний оригинал документа
Англо-русский словарь нормативно-технической терминологии > test current
-
Если испытательный ток ниже номинальной наибольшей отключающей способности, на выходной стороне выключателя следует предусмотреть дополнительные импедансы Z1.
-
2 test current
-
3 test current
Большой англо-русский и русско-английский словарь > test current
-
4 test current
-
5 test current
-
6 test current
Техника: испытательный ток -
7 test current
ток, испытательныйАнгло-русский словарь по ядерным испытаниям и горному делу > test current
-
8 test current
испытательный токEnglish-Russian dictionary of technical terms > test current
-
9 test current
-
10 maximum test current
3.16 максимальный испытательный ток (maximum test current) Iмакс: Больший из двух токов записи, используемых для испытаний магнитных полос на тонких гибких картах.
Источник: ГОСТ Р ИСО/МЭК 15457-2-2006: Карты идентификационные. Карты тонкие гибкие. Часть 2. Способы магнитной записи оригинал документа
Англо-русский словарь нормативно-технической терминологии > maximum test current
-
11 minimum test current
3.18 минимальный испытательный ток (minimum test current) Iмин: Меньший из двух токов записи, используемых для испытаний магнитных полос на тонких гибких картах.
Источник: ГОСТ Р ИСО/МЭК 15457-2-2006: Карты идентификационные. Карты тонкие гибкие. Часть 2. Способы магнитной записи оригинал документа
Англо-русский словарь нормативно-технической терминологии > minimum test current
-
12 AC test current
Измерительные приборы: испытательный переменный ток -
13 DC test current
Измерительные приборы: испытательный постоянный ток -
14 non-destructive test current
Космонавтика: безопасный ток испытанийУниверсальный англо-русский словарь > non-destructive test current
-
15 test
1. испытание, проверка; опыт; проба; исследование, анализ || испытывать, проверять; исследовать; производить анализ2. опробование ( скважины) || опробоватьrule of thumb test — грубый [приближенный] метод оценки
— ball indentation test— Charpy impact test— DAP test— dry test— hydraulic pressure test— Izod impact test— shearing test— torsional test— wearing test
* * *
1. испытание, испытания; проверка; контроль2. исследование; анализ3. критерийdrill stem formation test — исследование пласта пластоиспытателем, спускаемым на бурильных трубах
— use test
* * *
исследование; испытание; опыт; проверка
* * *
опыт; испытание, проверка; проверять
* * *
1) испытание, испытания; проба; проверка; контроль2) исследование; анализ4) опробование ( скважины) || опробовать6) критерий•test for color stability — испытания ( бензина) на стабильность цвета;
test for defect — проверка на наличие дефектов;
test for soundness — испытания ( цемента) на равномерность изменения объёма;
test for suitability — испытания на пригодность (); испытания на соответствие заданным требованиям;
to test a core for shows of oil — исследовать керн на признаки нефти;
to test a well — измерять дебит скважины;
to apply boring test — применять бурение при поисковых работах;
test to destruction — испытания до разрушения ( образца), разрушающие испытания;
test to failure — испытания до отказа;
to put to test — подвергать испытаниям;
test with recovery — испытания с восстановлением;
- abrasion testtest without destruction — испытания без разрушения ( образца), неразрушающие испытания;
- accelerated test
- accelerated aging test of gasoline
- acceleration inertia load test
- acceptance test
- acid heat test
- activity test
- adhesion test
- air pressure test
- alkali test
- angularity test
- aniline test
- appraisal test
- assessment test
- ASTM test
- audit test
- availability acceptance test
- azimuth test
- back-pressure test
- back-pressure formation test
- bailing test
- bearing test
- bedrock test
- blowdown test
- bottle test
- breakdown test
- burn-in reliability test
- carbon test
- carbon color test
- casing-packer formation test
- centrifuge test
- certification test
- charcoal test
- charcoal weight test
- checkout test
- cloud test of petroleum oil
- coke test
- coking test
- cold test
- combined environment reliability test
- complete destructive test
- complete functional test
- cone penetrometer test
- confirmation test
- confirmatory test
- consumption test
- contact test
- contamination test
- control test
- controlled test
- copper dish gum evaporation test
- copper dish residue test
- copper strip test
- corrosion test
- corrosive wear test
- cracking test
- crankcase oil dilution test
- crankcase oil foaming test
- crosstalk test
- current production rate test
- damaging test
- deep test
- deep pool test
- definitive test
- demulsibility test
- demulsification test
- development test
- diammonium phosphate test
- diesel-fuel distillation test
- diesel-fuel gravity test
- dilution test of fuel
- dip test
- direct oxidation test
- distillation test
- doctor test
- double casing-packer formation test
- double wall-packer formation test
- drawdown test
- drift test
- drilling mud density test
- drilling mud fluidity test
- drill-off test
- drill-stem formation test
- dry test
- eddy-current test
- emulsification test
- endurance test
- engineering design test
- engineering evaluation test
- equipment operation test
- evaporation test of gasoline
- evaporation gum test
- exploratory test
- extension test
- fail-safe test
- failure test
- failure-producing test
- failure-rate test
- failure-terminated test
- failure-truncated test
- failure-under-load test
- falling weight test
- fatigue test
- field test
- field compression test
- field maintenance test
- filter test
- filtration test
- final malfunction test
- fire test
- firing time test
- flammability test
- float test
- floc test
- flood pot test
- flow test
- flowing bottom hole pressure test
- fluid test
- foam test
- forced failure test
- formation test
- formation productivity test
- friability test
- fuel dilution test
- full-scale test
- full-scale fatigue test
- gas test
- gas flow test
- gas impermeability test
- gasoline precipitation test
- gasoline sulfur test
- gasoline tetraethil lead test
- gasoline volatility test
- gel strength test
- glass dish evaporation test
- glass dish gum test
- Green test
- guarantee test
- gum test
- gumming test
- hammer test
- hand test
- heavy-duty test
- hot test
- hot filtration test
- hydraulic-pressure test
- hydro test
- hydrogen-in-petroleum test
- hydrostatic test
- immersion test
- in-place test
- in-use life test
- inflammability test
- initial well potential test
- injectivity test
- injectivity-index test
- interference test
- intermodulation test
- kauri-butanol solvency test
- knock test
- laboratory test on crude
- laboratory test on oil
- lacquer test
- lamp burning test
- lamp sulfur test
- lead acetate test
- leak test
- leakage test
- leakage test of weld seams
- length-of-life test
- life test
- life-certification test
- line test
- logging-cable formation test
- longevity test
- lubricating oil emulsion test
- lubricating oil metal test
- magnetic polarity test
- maintainability test
- maintenance test
- marine explosure test
- mercurization test
- mercury freezing test
- mixing water test
- motor method test
- multirate flow test
- neutralization test
- nitrating test
- nonfoaming test
- nonreplacement test
- oil cold test
- oil corrosion test
- oil emulsion test
- oil well potential test
- Oliensis spot test
- on-site test
- open-flow test
- open-hole formation test
- operability test
- operating life test
- operational test
- operational readiness test
- operational readiness and reliability test
- operational readiness inspection test
- operational suitability test
- oven test
- overflow test
- overspeed test
- overstress reliability test
- oxidation test
- oxygen absorption test
- pass-fail test
- penetration test
- performance test
- periodic potential test
- periodic well potential test
- permeability test
- pipeline immersion test
- plam test
- porcelain dish test
- postcompletional flow test
- potential test
- predemonstration test
- preliminary qualification test
- preoverhaul test
- prepilot mining test
- prequalification test
- pressure test
- pressure building test
- pressure drawdown test
- pressure transient test
- producing test
- production test
- production reliability test
- productivity test
- product-proof test
- proof test
- pulling test
- pulse test
- qualification test
- quality verification test
- reaction test
- reflection test
- refraction test
- reliability test
- reliability assurance test
- reliability audit test
- reliability demonstration test
- reliability field test
- reliability growth test
- reliability production test
- reliability verification test
- repair test
- repeated bending stress test
- repeated compression test
- repeated direct stress test
- repeated dynamic stress test
- repeated impact tension test
- repeated stress test
- repeated tensile stress test
- repeated tension test
- repeated torsion test
- replacement test
- reservoir limit test
- reversion test of kerosene
- rheometric test
- ring test
- road knock test
- rock specimen test
- running test
- sampling reliability test
- seawater corrosion test
- sediment-and-water test
- sedimentometric test
- seismic test
- selective flow test of well
- sequential reliability test
- service test
- serviceability test
- service-life evaluation test
- setting-time test
- settlement test
- severe-duty test
- shallover pay test
- short-time well test
- shut-in pressure test
- sieving test
- silica test
- silicotungstic acid test
- sludge test
- sludging test
- smell test
- smoke test
- soap hardness test
- soundness-and-fineness test
- spot test
- spot quality test
- stability test
- standard test
- standard acid test
- standard distillation test
- steady-state test of well
- steam soak test
- step-rate test
- straddle test
- straddle packer drill stem test
- straight-hole test
- strata test
- submersion test
- suitability test
- sulfated residue test
- sulfur test
- sulfuric acid heat test
- system operation test
- tap test
- tensile test
- tensile-and-compression test
- tensile-fatigue test
- tensile-impact test
- tensile-shock test
- tension test
- thickening-time test
- through-casing formation test
- time-terminated reliability test
- torque test
- torsion test
- torsion impact test
- toughness test
- trial test
- tribotechnical test
- Tutwiler test
- twisting test
- type test
- undestructive test
- upsetting test
- up-the-hole test
- use test
- vane test
- varnish test
- verification life test
- viscosity test
- volatilization test
- wall building test
- wall-packer formation test
- warranty test
- water test
- water-and-oil content test
- waterflood core test
- water-loss test
- wear test
- weld test
- weldability test
- welding test
- well test
- well potential test
- winterization test
- wireline formation test
- withdrawal test* * * -
16 test
1) испытание
2) испытательный
3) испытывать
4) опробование
5) проба
6) пробовать
7) тест
8) <engin.> опыт
9) пробный
10) проверять
11) критерий
12) признак
13) проверка
14) испытующий
15) эксперимент
16) тестовый
17) замер
18) проверочный
19) обнаружение
20) определение
21) исследовать
22) выверять
23) контрольный
– abbreviated test
– ability test
– abrasion test
– accelerated test
– acceptance test
– acid test
– ageing test
– arbitration test
– articulation test
– bench test
– bend test
– bend-over test
– bending test
– bending-unbending test
– best test
– biological test
– blank test
– blow-pipe test
– boiling test
– bond test
– breakdown test
– breaking test
– buckling test
– burning test
– busy test
– calibration test
– capillary test
– carry out a test
– centrifuge test
– chi-square test
– cohesion test
– cold test
– cold-pressing test
– collapsibility test
– color test
– coloring test
– combustibility test
– comparison test
– comprehensive test
– compression test
– consumption test
– continuity test
– corrosion test
– cracking test
– creep test
– critical test
– crushing test
– cupel test
– cupping test
– decantation test
– desctructive test
– destruction test
– destructive test
– development test
– do test
– drop test
– duplicate test
– durability test
– eddy-current test
– efficiency test
– elasticity test
– endurance test
– equal-tails test
– Erichsen test
– etch test
– evaporation test
– expansion test
– extraction test
– failure-rate test
– fat test
– fatigue test
– field test
– flammability test
– flange test
– flanging test
– flare test
– flash-point test
– flattening test
– flexure test
– flight test
– floating test
– flow test
– fluidity test
– flutter test
– fracing test
– fracture test
– free-bend test
– free-fall test
– free-flight test
– freezing test
– friability test
– friction test
– fuel-consumption test
– full-scale test
– fusion test
– game test
– goodness-of-fit test
– grindability test
– ground test
– hardenability test
– hardness test
– heat test
– hot twist test
– hot upset test
– humidity test
– hydrostatic test
– icing test
– immersion test
– impact test
– impulse test
– impulse-withstand test
– intelligence test
– jet test
– jumping-up test
– laboratory test
– leakage test
– life test
– liquid-penetrant test
– load test
– long-run test
– longevity test
– macrosolubility test
– magnetic-particle test
– material test
– medial test
– melting test
– microharness test
– microsolubility test
– model test
– no-load test
– non-destructive test
– notch-bar test
– oil dilution test
– oscillation test
– overload test
– overspeed test
– oxidation test
– paint rub test
– panel-spalling test
– pass a test
– pass the test
– peel test
– perfomance test
– performance test
– pickle test
– preliminary test
– pressure test
– primary test
– pull test
– quench test
– quick test
– random test
– referee test
– regression test
– relaxation test
– reliability test
– remolding test
– reverse-bend test
– ringing test
– road test
– root test
– routine test
– run test cut
– salt-mist test
– scratch-hardness test
– screen test
– sedimentation test
– shatter test
– shearing test
– short-term test
– shrinkage test
– sign test
– significance test
– single-end test
– site test
– skein test
– slaking test
– solubility test
– spark test
– splitting test
– spoon test
– spray test
– stopping test
– strength test
– stress test
– stress-rupture test
– subjective test
– survival test
– tackiness test
– tear test
– tensile test
– test baking
– test bank
– test borehole
– test card
– test case
– test certificate
– test chart
– test condition
– test connector
– test current
– test desk
– test device
– test diagram
– test electrolyte
– test equipment
– test facility
– test flight
– test for
– test for convergence
– test for defects
– test for end
– test for leak-proofness
– test for minimum
– test function
– test hypothesis
– test input
– test jack
– test key
– test lead
– test load
– test metal
– test mine
– test mock-up
– test model
– test needle
– test of convergence
– test of homogeneity
– test of hypothesis
– test of location
– test of normality
– test of whether
– test oscillator
– test paper
– test particle
– test pattern
– test piece
– test pilot
– test pole
– test pressure
– test pulse
– test reaction
– test relay
– test report
– test rig
– test rod
– test run
– test set
– test set-up
– test shot
– test specimen
– test stand
– test station
– test technique
– test terminal
– test to failure
– test tree
– test unit
– test voltage
– test weld
– thermal test
– torsion test
– total-lot test
– toughness test
– towing test
– type test
– ultraviolet test
– unbiased test
– upsetting test
– vacuum test
– vibration-survival test
– voltage test
– Votchal-Tiffeneau test
– warranty test
– wear test
– weld test
– weldability test
Abel test for convergence — <math.> признак сходимости Абеля
distribution-free test of fit — непараметрический критерий согласия
international test conference — международная конференция по методам и средствам испытаний
most powerful test — <math.> критерий наиболее мощный
notched test bar — <metal.> образец надрезанный
pulse-reflection ultrasonic test — ультразвуковая дефектоскопия эхом
standard test solution — <energ.> раствор модельный
test compression factor — <comput.> коэффициент сжатия тестов
test for uniform convergence — признак равномерной сходимости
test statistical hypothesis — проверять статистическую гипотезу
-
17 current
1) течение; поток4) вчт. текущая запись•-
absorption current
- ac anode current -
action current
-
active current
-
actuating current
-
admissible continuous current
-
air current
-
alongshore current
-
alternate current
-
anode current
-
arbitrary noise current
-
arc current
-
arc-back current
-
arcing ground fault current
-
armature current
-
ascending current
-
audio-frequency current
-
avalanche current
-
back current
-
back short circuit current
-
backward current
-
barogradient current
-
base current
-
beam current
-
bearing currents
-
beating current
-
beat current
-
biasing current
-
bias current
-
biphase current
-
bleeder current
-
blind current
-
blowing current
-
body current
-
bottom current
-
boundary current
-
braking current
-
branch current
-
break induced current
-
breakaway starting current
-
breakdown current
-
breaking current
-
bucking current
-
bulk current
-
bypass current
-
capacitance current
-
capacitive current
-
capacity current
-
carrier current
-
cathode current
-
channel current
-
charging current
-
circulating current
-
circumpolar current
-
collector current
-
complex sinusoidal current
-
complex current
-
conduction current
-
conjugate complex sinusoidal current
-
conjugate complex current
-
constant current
-
consumption current
-
continuous current
-
continuous traction current
-
control current
-
convection current
-
core-loss current
-
creeping current
-
critical current
-
cross current
-
crystal current
-
current of realm
-
current of run-unit
-
current of set
-
cutoff current
-
damped alternating current
-
damped current
-
dark current
-
deep-water current
-
deep current
-
delta currents
-
density current
-
descending current
-
design current
-
dielectric absorption current
-
dielectric current
-
diffusion current
-
direct current
-
direct-axis current
-
discharge current
-
discontinuous current
-
displacement current
-
downward current
-
drift current
-
drive current
-
drop-away current
-
earth current
-
earth fault current
-
eddy currents
-
effective current
-
electric current
-
electrode current
-
electrolysis current
-
electron current
-
electron-beam induced current
-
emission current
-
emitter current
-
equalizing current
-
equivalent input noise current
-
excess current
-
exchange current
-
excitation current
-
external current
-
extra current
-
extraction current
-
extraneous current
-
feedback current
-
field current
-
filament current
-
firing current
-
flood current
-
fluctuating current
-
focusing-coil current
-
focus current
-
fold back current
-
follow current
-
forced alternating current
-
forced current
-
foreign currents
-
forward current
-
Foucault currents
-
free alternating current
-
free current
-
full-load current
-
fusing current
-
galvanic current
-
gas current
-
gate current
-
gate nontrigger current
-
gate trigger current
-
gate turnoff current
-
generation-recombination current
-
gradient current
-
grib current
-
ground current
-
ground-return current
-
harmonic current
-
heat current
-
heater current
-
high-frequency current
-
high-level input current
-
high-level output current
-
holding current
-
hold current
-
hold-on current
-
hole current
-
idle current
-
image current
-
impressed current
-
incident current
-
induced current
-
initial current
-
injection current
-
inphase current
-
input current
-
input leakage current
-
input offset current
-
inrush current
-
inshore current
-
instantaneous carrying current
-
instantaneous current
-
insulation current
-
interference current
-
intermittent current
-
inverse current
-
ion production current
-
ionic current
-
ion current
-
ionization current
-
irradiation-saturation current
-
lagging current
-
latching current
-
leading current
-
leakage current
-
let-go current
-
light current
-
lightning current
-
line charging current
-
linear current
-
load current
-
locked-rotor current
-
loop current
-
loss current
-
low-level input current
-
low-level output current
-
magnetization current
-
majority-carrier current
-
majority current
-
make induced current
-
make-and-brake current
-
making current
-
maximum power current
-
minority-carrier current
-
minority current
-
motor inrush current
-
nearshore current
-
near-surface current
-
net current
-
neutral current
-
neutron current
-
neutron diffusion current
-
noise current
-
no-load current
-
nonsinusoidal current
-
nontrigger current
-
non-turn-off
-
offset current
-
offshore current
-
off-state current
-
on-state current
-
open-circuit current
-
operating current
-
output current
-
overload current
-
parasitic current
-
peak arc current
-
peak current
-
peak switching current
-
peak withstand current
-
peak-point current
-
peak-to-peak current
-
perception current
-
periodic current
-
persistent current
-
phase current
-
phase-fault current
-
phasor current
-
photo-electric current
-
photo current
-
photo-generated current
-
photo-induced current
-
pickup current
-
piezoelectric current
-
pinch current
-
plasma current
-
polarization current
-
polyphase current
-
postarc current
-
power current
-
power follow current
-
prebreakdown current
-
preconduction current
-
primary current
-
principal current
-
probe current
-
pull-in current
-
pulsating current
-
pulse current
-
pyroelectric current
-
quadrature-axis current
-
quiescent current
-
rated current
-
rated temperature-rise current
-
reactive current
-
read current
-
recombination current
-
rectified current
-
reflected current
-
regulated current
-
relative short-circuit current
-
release current
-
residual current
-
rest current
-
return current
-
reverse current
-
reverse-biased current
-
reverse-induced current
-
RF current
-
ringing current
-
rip current
-
ripple current
-
root-mean-square current
-
running current
-
rupturing current
-
saturated drain current
-
saturation current
-
saw-tooth current
-
secondary current
-
secondary-electron emission current
-
shaft currents
-
sheath current
-
shelf current
-
shield current
-
shock current
-
short-circuit current
-
short-noise current
-
short-time thermal current
-
short-time withstand current
-
sine-wave current
-
single-phase current
-
sinusoidal current
-
slope current
-
sneak current
-
spindle-motor current
-
split current
-
stalled-motor current
-
standby current
-
standing current
-
star currents
-
starter current
-
steady leakage current
-
steady surface current
-
steady volume current
-
steady-state current
-
stray current
-
stroke current
-
subsurface current
-
subsynchronous frequency current
-
subsynchronous current
-
subtransient armature current
-
superconduction current
-
superimposed current
-
supply current
-
surface current
-
surface-leakage current
-
surge current
-
suspension current
-
sustained current
-
sustaining current
-
switched current
-
switching current
-
symmetrical alternate current
-
synchronizing current
-
telluric current
-
test current
-
thermal current
-
thermal noise current
-
thermionic current
-
thermostimulated current
-
three-phase current
-
threshold current
-
through current
-
tidal current
-
tolerance current
-
traction current
-
traffic current
-
transfer current
-
transient current
-
transient-decay current
-
transmission-line current
-
trigger current
-
turbidity current
-
turnoff current
-
turn-on current
-
two-phase current
-
undulating current
-
unidirectional current
-
unsymmetrical currents
-
upward current
-
valley point current
-
variable current
-
vector current
-
virtual current
-
voice-frequency current
-
voltaic current
-
wattful current
-
wattless current
-
welding current
-
whirling currents
-
wind current
-
withdrawal current
-
working current
-
work current
-
Zener current
-
zero-sequence current -
18 current
1) поток
2) водоток
3) текущий
4) токовой
5) токовый
6) значение тока
7) имеющийся
8) <electr.> сила тока
9) сложившийся
10) течение
11) общеупотребительный
– absorption current
– alternating current
– antenna current
– ascending current
– avalanche current
– back current
– beam current
– bias current
– biasing current
– black current
– bunched current
– capacitive current
– Caribbean Current
– carry current
– carrying current
– charging current
– conduction current
– constant current
– consumption current
– control current
– convection current
– current algebra
– current amplification
– current balance
– current build-up
– current check
– current circuit
– current collector
– current consumption
– current crowding
– current density
– current distribution
– current divider
– current divides
– current drain
– current efficiency
– current events
– current feedback
– current gain
– current inrush
– current installing
– current instruction
– current intensity
– current limiter
– current limiting
– current margin
– current meter
– current noise
– current overload
– current path
– current production
– current protection
– current receiver
– current regulation
– current relay
– current rise
– current saturation
– current sensitivity
– current sheet
– current stabilization
– current stabilizer
– current standards
– current supply
– current task
– current transformer
– current triangle
– current vector
– current velocity
– current wave
– dark current
– decaying current
– descending current
– direct current
– discharge current
– displacement current
– double current
– drift current
– drop-out current
– dynode current
– eddy current
– emission current
– erasing current
– exchange current
– exciting current
– external current
– extraneous current
– fault current
– fault-to-earth current
– feed current
– feedback current
– field current
– filament current
– forward current
– full-select current
– fusing current
– gas current
– grid current
– half-select current
– holding current
– hole current
– in-phase current
– in-rush current
– induce current
– inhibit current
– input current
– instantaneous current
– ion current
– Kuroshio current
– large-scale air current
– large-scale current
– latching current
– leakage current
– let-go current
– line current
– load current
– loop current
– loss current
– magnetizing current
– marking current
– no-load current
– noise current
– non-sinusoidal current
– operate current
– operating current
– oscillating current
– Oudin current
– output current
– overload current
– partial-select current
– peak current
– penetration of current
– photocathode current
– plasma current
– plate current
– polarization current
– polyphase current
– preionization current
– primary current
– pulsating current
– pyroelectric current
– quiescent current
– r f current
– random current
– rated current
– read current
– recombination current
– rectified current
– rectify current
– residual current
– ringing current
– roaming current
– root-mean-square current
– saturation current
– saw-tooth current
– sea current
– sea current meter
– secondary current
– selection current
– self-inductance current
– set of current
– short-circuit current
– space-charge current
– speaking current
– spurious current
– standing current
– starting current
– stray current
– stream current
– strong current
– sweep current
– synchronizing current
– telluric current
– test current
– thermionic current
– three-phase current
– to be current
– transient current
– tunnel current
– wandering current
– welding current
– white current
– word current
– write current
alternating current motor — электродвигатель переменнего тока
amplitude of tidal current — <geogr.> амплитуда приливного течения
current regulator tube — <tech.> барретер, барретор, барреттер, токостабилизатор
equation for alternating current — уравнение переменного тока
short circuit current — <electr.> ток короткого замыкания
South Equatorial Current — <geogr.> течение Южное Пассатное
space-charge limited current — <electr.> ток ограниченный пространственным зарядом
variable current transformer — трансформатор переменного тока
zero signal current — <electr.> ток покоя
-
19 test
1) испытание; испытания || испытывать2) проверка; контроль || проверять; контролировать3) тест; тестирование || тестировать5) стат. критерий•- accelerated testto dry test — испытывать без резания, испытывать станок без резания, испытывать на холостом ходу
- acceptance test
- alignment test
- alternative test
- angular test
- approval test
- axial load test
- axial test
- back-to-back test
- balance test
- bar-to-bar test
- benchmark test
- bend test
- bending fatigue test
- bending test
- bend-over test
- black-band test
- blow-bending test
- blueing test
- bond test
- brake test
- braking test
- breaking test
- Brinell hardness test
- Brinell test
- buckling test
- calibrated driving machine test
- calibration test
- calorimetric test
- camera-aided test
- carbon test
- certification test
- Charpy impact test
- Charpy test
- check test
- check-out test
- closure test
- cold bend test
- cold pressing test
- collision test
- commissioning test
- commutation test
- comparative test
- compression test
- computer-aided design and test
- computer-assisted fault isolation test
- cone-indentation test
- cone-thrust test
- conformance test
- controlled test
- core test
- corrosion fatigue test
- corrosion test
- creep test
- cutting test
- deflection tests
- destruction test
- destructive test
- determinative test
- development test
- developmental test
- diagnostic test
- diamond-pyramid hardness test
- discrimination test
- disk test
- drawing test
- driving test
- driving-profile test
- drop test
- durability test
- dynamic test
- dynamometer test
- eddy current test
- efficiency test
- electrical back-to-back test
- end-to-end test
- endurance test
- environmental test
- etching test
- evaluation test
- extraction test
- facing test
- factory test
- fatigue test
- fault detection test
- fault location test
- field test
- final test
- flattening test
- flex life test
- flexural test
- flexure test
- forging test
- friction test
- frictional test
- full-scale test
- functional test
- gear life test
- geometric test
- geometrical test
- grab test
- ground test
- hardness test
- harmonic test
- high-voltage test
- hydraulic pressure test
- hydraulic test
- identification tests
- impact test
- impulse test
- in-process test
- inspection test
- investigation test
- Jominy test
- L-2 test
- lab test
- laboratory test
- leak test
- life test
- light load test
- load test
- machinability test
- machine tool alignment test
- machine tool test
- machining performance test
- magnetic test
- maintenance test
- mechanical test
- micrographic test
- monitoring test
- noise-level test
- no-load test
- nondestructive test
- official test
- open-circuit test
- operating test
- optimality test
- out-of-control tests
- overhead load test
- overload test
- overspeed test
- peel test
- performance test
- periodic test
- periodical test
- practical test
- precision test
- predelivery test
- preinstallation test
- preliminary test
- preproduction test
- preventive test
- production test
- production-type test
- profile tests
- proof test
- qualification test
- quality assurance test
- quality conformance test
- quality performance test
- random test
- ravel test
- reduced test
- reliability compliance test
- reliability determination test
- reliability test
- response test
- retardation test
- rig test
- roller fatigue test
- roller life test
- routine check tests
- routine test
- running test
- rupture test
- safety test
- saline droplet corrosion test
- sampling test
- scoring test
- sequential test
- service test
- shear test
- shearing test
- shock test
- short test
- simulated service test
- single test
- soft test
- sound test
- special test
- stability test
- standard test
- starting test
- state tests
- static bending test
- static test
- step stress test
- storage test
- straightening test
- strength test
- strip test
- sudden short-circuit test
- sustained power test
- sustained short-circuit test
- tear test
- tear-apart test
- temperature-rise test
- tensile test
- tension test
- test of the accuracy
- thermal test
- time-restricted test
- tool wear test
- torsional test
- transportability test
- trouble-free assurance test
- trouble-free quality assurance test
- Turing test
- twist test
- twisting test
- type approval test
- type test
- upsetting test
- use test
- validation test
- vibration test
- waveform test
- wear test
- working testEnglish-Russian dictionary of mechanical engineering and automation > test
-
20 test
1. испытание, тест2. проверка, оценка4. проба5. испытывать, проверять (see also testing)6. пробоватьabrasion test — 1) испытание на истирание [абразивный износ] 2) испытание царапанием
abrasive hardness test — 1) склерометрическое испытание на твёрдость 2) склерометрическое определение твёрдости
abruption test — испытание на разрыв
absorption test — испытание на поглощение, определение влагостойкости
accelerated test — 1) ускоренное [сокращённое] испытание 2) экспресс-анализ
acceleration test — испытание на воздействие ускорений
acid-proof test — испытание на кислотостойкость
adhesion test — испытание на адгезию [прочность сцепления], испытание прочности склейки
adhesive test — испытание прочности склейки, испытание на адгезию [прочность сцепления]
adiabatic-compression sensitivity test — испытание на чувствительность ( ракетного топлива) к адиабатическому сжатию
aging test — испытание на старение
air test — 1) испытание в воздушной среде 2) испытание на герметичность 3) испытание сжатым воздухом
alkali-proof test — испытание на щёлочестойкость
alternate-stress test — испытание ( на усталость) знакопеременной нагрузкой
alternating-bending test — испытание на знакопеременный изгиб
antiseptic test — испытание на антисептичность
artificial aging test — испытание на искусственное [ускоренное] старение
atmospheric stress corrosion test — испытание на коррозию под напряжением в атмосферных условиях
attrition test — испытание на износ
ball hardness test — испытание твёрдости вдавливанием шарика, определение твёрдости по Бринелю
indentation pressure test — определение твёрдости по Бринелю, испытание твёрдости вдавливанием шарика
bearing test — испытание на смятие [опорную прочность]
bending test — испытание на изгиб
bend-over test — испытание на изгиб
biaxial tension test — испытание на двухосное растяжение
bird impact test — испытание на пробой тушками птиц
blow test — 1) испытание на удар 2) испытание на ударную прочность
bond test — испытание на сцепление
bonding peel test — испытание на отслаивание склейки
breaking test — 1) испытание на разрушение, испытание на разрыв 2) испытание на излом
breakdown test — 1) испытание на разрушение, испытание на разрыв 2) испытание на излом
Brinell-hardness test — определение твёрдости по Бринелю
brittleness test — испытание на ломкость [хрупкость]
buckling test — испытание на продольный изгиб
bulk dilution test — испытание па всестороннее сжатие
bump test — 1) ударное испытание 2) испытание на ударную прочность
burning test — испытание на горение [горючесть]
burn-off test — испытание выжиганием ( для определения состава связующего)
bursting test — испытание с разрушением образца
cavitation test — испытание на кавитацию
Charpy impact test — испытание на удар по Шарпи, определение ударной вязкости по Шарпи
Charpy V-notch test — определение ударной вязкости образца с V-образным надрезом по Шарпи
charring ablator test — испытание обугливающегося [коксующегося] абляционного материала
chemical test — 1) химическое испытание 2) химический анализ
cleavage test — испытание на расщепление
climatic test — климатическое испытание, испытание на воздействие климатических условий
cold temperature test — испытание на морозостойкость, испытание при низких температурах
combustibility test — испытание на воспламенение [горючесть]
compatibility test — испытание на совместимость
complete destructive test — полное разрушающее испытание
composite test — испытание композиционного материала
compression test — испытание на сжатие
constant load test — испытание при постоянной нагрузке
corrosion test — испытание коррозионностойкости, коррозионное испытание
corrosion fatigue test — испытание на коррозионную усталость
corrosive wear test — испытание на окислительный износ
cracking test — коррозионное испытание на растрескивание
crack-propagation test — испытание на распространение трещин
crash test — испытание на разрушение
creep test — 1) испытание на ползучесть 2) испытание на текучесть
creep-rupture test — испытание на длительную прочность
cripling test — 1) испытание на продольный изгиб 2) испытание на перегиб
critical collapse test — испытание на устойчивость
cross-bending test — испытание на поперечный изгиб
crushing test — 1) испытание на раздавливание 2) испытание на раздробление
cryogenic temperature test — испытание при криогенных [низких] температурах
cupping test — испытание на вытяжку
curing test — испытание на вулканизацию
cycle test — циклическое испытание
cyclic test — циклическое испытание
cycle humidity test — циклическое испытание во влажной среде
cyclic-oxidation test — испытание на циклическое окисление
damping test — 1) испытание демпфирующих свойств 2) испытание на циклическую вязкость
deep-drawing test — испытание на глубокую вытяжку
deflection test — испытание на изгиб [прогиб]
deformation test — испытание на деформацию
delamination test — испытание на отслаивание
destruction test — испытание с разрушением ( образца)
destructive test — испытание с разрушением ( образца)
diamond-pyramide hardness test — определение твёрдости вдавливанием алмазной пирамиды ( по Виккерсу)
dielectric test — испытание диэлектрика [диэлектрических свойств]
direct compression test — испытание на двустороннее сжатие
drifting test — испытание на пробиваемость
drop-weight test — 1) испытание на удар падающим грузом 2) ударное испытание 3) определение ударной вязкости 4) копровое испытание
drop-weight tear test — ударное испытание на разрыв
dry strand test — испытание сухой пряди
ductile test — 1) испытание на вязкость 2) определение ударной вязкости
durability test — испытание на выносливость [долговечность]
dye-penetrant test — испытание методом красок, контроль проникающими красками
dynamic corrosion test — динамическое испытание на коррозию
elasticity test — испытание на упругость [эластичность]
electrolytic corrosion test — 1) испытание на электрохимическую коррозию 2) испытание электролита на коррозию
elevated-temperature test — испытание при повышенных температурах
elongation test — испытание на удлинение [растяжение]
endurance test — 1) испытание на выносливость [усталость] 2) испытание на прочность [стойкость] (например, лака или краски)
endurance tension test — испытание на выносливость при растяжении
endurance torsion test — испытание на выносливость при кручении
environmental test — испытание на воздействие окружающей среды
erosion test — испытание на эрозию
etching test — 1) испытание травлением 2) проба ( металла) травлением
explosive loading test — испытание взрывом, взрывное испытание
external hydrostatic test — испытание на внешнее гидростатическое давление
external pressure test — испытание на внешнее давление
falling ball test — испытание на упругость методом падающего шарика
falling sphere test — испытание на упругость методом падающего шарика
fatigue test — испытание на усталость [выносливость]
final test — испытание до разрушения
fire test — 1) испытание на огнестойкость 2) определение температуры воспламенения 3) огневое испытание ( двигателя)
fire-resistance test — испытание на огнестойкость
flammability test — испытание на воспламеняемость
flash test — определение температуры вспышки, испытание на воспламенение
flat-bending test — испытание на плоский изгиб
flattening test — испытание на сплющивание
flexural impact test — ударное испытание на изгиб
flexure test — испытание на изгиб
fluorescent test — флуоресцентный [люминесцентный] контроль
forging test — испытание на ковкость
fracture test — испытание на излом [разрушение]
freezing test — испытание на замораживание [морозостойкость]
friability test — испытание на хрупкость [ломкость]
friction test — испытание на трение
fuel-resistance test — испытание на топливостойкость
fungus test — испытание на грибостойкость
gamma-ray test — просвечивание гамма-лучами, гаммаграфический контроль
gas impermeability test — испытание на газонепроницаемость
gasoline-resistance test — испытание на бензиностойкость
gas permeability test — испытание на газопроницаемость
hammering test — испытание на ковкость
hanging test — испытание на разрыв подвешиванием грузов к образцу
hardenability test — проба на прокаливаемость
hardness test — испытание на твёрдость, определение твёрдости
heat test — испытание нагревом [на нагрев]
heat-resistance test — испытание на теплостойкость
heat-stability test — испытание на термическую устойчивость
high-pressure test — испытание при высоких давлениях
high-temperature test — 1) испытание на жаростойкость 2) испытание при высоких температурах
high-voltage test — испытание на выносливость высокого напряжения (например, изоляции)
horizontal shear test — испытание на сдвиг [срез] вдоль слоёв
hot test — 1) испытание в горячем состоянии, горячая проба 2) испытание на нагрев
humidity test — испытание во влажной среде
hydraulic pressure test — гидравлическое испытание
hydraulic tension ring test — гидравлическое испытание колец на растяжение
hydrostatic test — гидростатическое испытание
hysteresis test — испытание на гистерезис
immersion test — 1) испытание погружением образца 2) иммерсионный контроль
impact test — 1) испьггание на ударные нагрузки 2) испытание на удар 3) ударное испытание 4) определение ударной вязкости
indentation test — испытание на твёрдость вдавливанием (например, шарика или пирамиды)
insulation test — 1) испытание на изоляцию 2) испытание изоляции
interlaminar shear test — испытание на межслойный сдвиг
interlaminar tensile test — испытание на межслойное растяжение
internal hydrostatic pressure test — испытание на внутреннее гидростатическое давление
Knoop hardness test — испытание на микротвёрдость по Кнупу, определение микротвёрдости по Кнупу
life test — испытание на долговечность
light aging test — испытание на световое старение
light resistance test — испытание на светостойкость
loading test — статическое испытание, испытание нагружением
long-duration test — длительное испытание
long-time creep test — испытание на длительную прочность
low-temperature test — испытание при низких [криогенных] температурах, испытание на морозостойкость
magnetic test — магнитный контроль [дефектоскопия]
magnetic fluid test — магнитный контроль методом суспензии
magnetic particle test — контроль магнитными частицами
magnetic permeability test — испытание на магнитную проницаемость
magnetic perturbation test — контроль методом магнитного возмущения
magnetic powder test — магнитный контроль методом порошков, дефектоскопия магнитным порошком
mechanical test — испытание механических свойств, механические испытания
metallographic test — металлографическое исследование
meteorite-strike test — испытание на пробой [удар] метеоритами
micrograph test — металлографическое исследование
microhardness test — испытание на микротвёрдость, определение микротвёрдости
moisture absorption test — испытание на влагопоглощение
moisture permeability test — испытание на водопроницаемость
moisture-proofness test — испытание на влагостойкость [влагонепроницаемость]
moisture-resistance test — испытание на влагонепроницаемость [влагостойкость]
Mooney viscosity test — определение вязкости по Муни
Naval Ordnance Laboratory ring test — испытание кольцевых образцов по методу лаборатории вооружения ВМС США, испытание колец NOL
NOL ring test — испытание колец NOL, испытание кольцевых образцов по методу лаборатории вооружения ВМС США
NOL multiaxial fatigue test — многоосное испытание колец NOL на усталость
nondestructive test — 1) испытание без разрушения ( образца) 2) неразрушающий контроль
notched-bar impact test — испытание на удар надрезанного образца, определение ударной вязкости надрезанного образца
notched bend test — испытание на изгиб надрезанного образца
notched tensile test — испытание на разрыв надрезанного образца
notch shock test — испытание на ударную вязкость надрезанного образца
odor test — 1) испытание на запах 2) проба на запах
oil-resistance test — испытание на маслостойкость
outdoor exposure test — испытание [выдержка] на открытом воздухе
oven test — испытание на тепловое старение в печи
oxidation test — испытание на окисление
oxygen bomb test — испытание на искусственное старение в кислородной бомбе
ozone aging test — испытание на старение в озоне
peeling test — 1) испытание на отслаивание 2) испытание на отрыв
pendulum impact test — испытание на удар маятниковым копром
penetrant fluid test — контроль проникающей жидкостью
penetrant nondestructive test — контроль проникающим веществом без разрушения ( образца)
performance test — 1) испытание в эксплуатационных условиях 2) определение характеристик ( материала)
plasma torch test — испытание плазменной горелкой
plasticity test — 1) испытание на пластичность 2) определение пластичности
pliability test — 1) определение пластичности 2) испытание на пластичность
plastic range test — определение пределов пластичности
ply separation test — испытание на расслоение [отслоение]
porosity test — проба на пористость ( травлением)
pulling test — испытание на растяжение [разрыв]
pulsed eddy-current test — 1) проверка импульсными вихревыми токами 2) электроиндуктивная дефектоскопия
pure-bending test — испытание на чистый изгиб
qual test — испытание на соответствие техническим условиям
qualification test — испытание на соответствие техническим условиям
quenching test — проба на прокаливаемость
quick test — ускоренное испытание, экспресс-анализ
radiant-heating test — испытание на лучистый нагрев
radiation test — радиационное испытание
radiographic test — 1) радиографический контроль 2) рентгенографический контроль 3) гаммаграфический контроль
rebound test — испытание на эластичность по отскоку
reliability test — испытание на надёжность
repeated compression test — испытание на усталость при многократных сжатиях
repeated impact test — испытание на динамическую выносливость
repeated stress test — испытание на усталость [выносливость] при повторных нагрузках
repeated tension test — испытание на многократное растяжение
resin test — 1) испытание смолы 2) испытание связующего
reverse bending test — испытание на знакопеременный изгиб
ring test — кольцевое испытание, испытание кольцевого образца
Rockwell hardness test — определение твёрдости по Роквеллу
room-temperature burst test — разрывное испытание при комнатной температуре
room-temperature cycle test — циклическое испытание при комнатной температуре
rotational drop test — испытание на маятниковом копре
rupture test — испытание на разрушение [разрыв, прочность]
safe-life test — испытание на безопасный срок хранения ( ракетного топлива)
scleroscope hardness test — определение твёрдости по склероскопу, склероскопическое испытание на твёрдость
scratch hardness test — испытание на твёрдость царапанием, определение твёрдости по Моосу
separation test — испытание на расслоение
service test — испытание в эксплуатационных условиях, эксплуатационное испытание
shearing test — испытание на сдвиг [срез, скалывание]
shock test — испытание на удар, ударное испытание
shock-bending test — испытание на изгиб ударом
Shore indentional test — определение твёрдости по Шору
Shore scleroscope test — определение твёрдости по Шору
short-time test — кратковременное испытание, экспресс-испытание, экспресс-анализ
sieve test — ситовый анализ
sieving test — ситовый анализ
simulated environment test — испытание в условиях, имитирующих окружающую среду
simulated space test — испытание в условиях, имитирующих космические
sintering test — испытание на спекаемость
size test — гранулометрический анализ
sizing test — гранулометрический анализ
sonic test — испытание ультразвуковым методом
space test — испытание в космических условиях
specific-gravity test — определение удельного веса
standard test — 1) стандартное [типовое] испытание 2) стандартная проба
static test — статическое испытание
static-fatigue test — статическое испытание на усталость
static notched bend test — статическое испытание на изгиб надрезанного образца
static vibration test — статическое испытание на вибрацию
stiffness test — испытание на жёсткость
strain-cycling test — испытание методом циклического деформирования
strength test — 1) испытание па прочность 2) определение временного сопротивления
stress-corrosion test — испытание на коррозию под напряжением
stress-durability test — испытание на длительную прочность [статическую усталость]
stress relaxation test — испытание на релаксацию напряжений
stretching test — испытание на растяжение [сопротивление разрыву], испытание на удлинение при разрыве
strip peel test — испытание на отслаивание ленты
structural test — испытание на прочность
tearing test — 1) испытание на разрыв [раздир] 2) испытание на износ
temperature test — температурное испытание, испытание на нагрев
tenacity test — 1) испытание на разрыв 2) испытание на растяжение 3) испытание на вязкость [прилипание]
tensile test — 1) испытание на разрыв 2) испытание на растяжение
tensile fatigue test — испытание на усталость при растяжении
tensile impact test — 1) ударное испытание на разрыв 2) ударное испытание на растяжение
tensile shock test — 1) ударное испытание на растяжение 2) ударное испытание на разрыв
tensile strength test — определение временного сопротивления на растяжение, испытание на разрыв
tension test — 1) испытание на растяжение 2) определение диаграммы растяжения
tension fatigue test — испытание на усталость при растяжении
thermal test — тепловое [термическое] испытание
thermal fatigue test — испытание на термическую усталость, термоциклическое испытание
thermal shock test — испытание на тепловой удар
thermomechanical test — термомеханическое испытание
torque test — испытание на кручение [скручивание]
torsional test — испытание на скручивание [кручение]
torsion shear test — испытание на срез при скручивании
toughness test — испытание на ( ударную) вязкость
tracer test — испытание методом меченых атомов
transverse-bending test — испытание на поперечный изгиб
twisting test — испытание на кручение [скручивание]
uniaxial shear test — испытание на чистый сдвиг
uniaxial tensile test — испытание на одноосное растяжение
uninflammability test — испытание на невоспламеняемость
unnotched tensile test — испытание на разрыв ненадрезанного образца
upsetting test — испытание на раздачу ( труб)
vacuum test — испытание в вакууме
vibration test — испытание на вибрацию [вибропрочность]
vibroacoustic test — виброакустическое испытание
Vickers diamond-pyramide hardness test — определение твёрдости вдавливанием алмазной пирамиды по Виккерсу
Vickers hardness test — испытание на твёрдость по Виккерсу, определение твёрдости по Виккерсу
viscosity test — испытание на вязкость, определение вязкости, реологическое испытание
V-notch test — испытание образца с V-образным надрезом
V-notch impact test — испытание на удар образца с V-образным надрезом
waterproof test — испытание на водостойкость
wearing test — 1) испытание на износ 2) испытание на истирание
weathering test — 1) испытание на старение в атмосферных условиях 2) испытание на погодостойкость
weatherproof test — 1) испытание на погодостойкость 2) испытание на атмосферную коррозию
weight-loss test — испытание на коррозию по убыли веса образца
weldability test — испытание на свариваемость
welding test — испытание на свариваемость
X-ray test — 1) рентгеновское [рентгеноскопическое] испытание 2) рентгеновский [рентгенографический] анализ
English-Russian dictionary of aviation and space materials > test
См. также в других словарях:
test current for low temperatures — The specification for assessing battery starting behavior at low temperatures and under given conditions; indicated in amps on the battery case … Dictionary of automotive terms
Test and tagging — is a generic name given to the process of visually inspecting and electrically testing in service electrical equipment for personal use and/or safety. Colloquially, it is also referred to as; tagging, test tag, test and tag, electrical tagging,… … Wikipedia
Current mirror — A current mirror is a circuit designed to copy a current through one active device by controlling the current in another active device of a circuit, keeping the output current constant regardless of loading. The current being copied can be, and… … Wikipedia
current for low temperatures — See test current for low temperatures … Dictionary of automotive terms
Current Issues and Events — (commonly known as Current Events) is one of several academic events sanctioned by the University Interscholastic League. The contest began in the 1990 91 scholastic year.Current Events is designed to test students knowledge and understanding of… … Wikipedia
Current Issues and Events (UIL) — Current Issues and Events (commonly known as Current Events) is one of several academic events sanctioned by the University Interscholastic League. The contest began in the 1990 91 scholastic year. Current Events is designed to test students… … Wikipedia
Test Match Special — (known as TMS ) is a radio programme broadcast on BBC Radio 4 (long wave), Five Live Sports Extra (digital) and the internet to the United Kingdom and (where broadcasting rights permit) the rest of the world, including England s winter tours to… … Wikipedia
Test (Unix) — test is a Unix command that evaluates conditional expressions.yntax test expression or [ expression ] DescriptionThe test command evaluates the expression parameter. In the second form of the command, the [ ] (brackets) must be surrounded by… … Wikipedia
Test Rorschach — Test de Rorschach La première planche parmi les dix du test de Rorschach Le test de Rorschach ou psychodiagnostik est un outil d évaluation psychologique de type projectif élaboré par le psychiatre et psychanalyste Hermann Rorschach en 1921. Il… … Wikipédia en Français
Test de rorschach — La première planche parmi les dix du test de Rorschach Le test de Rorschach ou psychodiagnostik est un outil d évaluation psychologique de type projectif élaboré par le psychiatre et psychanalyste Hermann Rorschach en 1921. Il consiste en une… … Wikipédia en Français
Test des taches d'encre — Test de Rorschach La première planche parmi les dix du test de Rorschach Le test de Rorschach ou psychodiagnostik est un outil d évaluation psychologique de type projectif élaboré par le psychiatre et psychanalyste Hermann Rorschach en 1921. Il… … Wikipédia en Français